SELF TAPPING THREADED INSERT W. THREE CUTTING HOLE

SELF TAPPING THREADED INSERT
W. THREE CUTTING HOLE

MATERIAL AVAILABLE: 
STEEL, STAINLESS STEEL, ALUMINUM, ALUMINUM ALLOY, BRASS

FOR USE IN THICK WALL OR CLOSE TO AN EDGE

ADVANTAGE:
1.HIGH PULL-OUT STRENGTH
2.HIGH TORQUE RESISTANCE
3.STRONG WEAR RESSTANCE THREAD
4.FAST, EASY INSTALLATION
5.EXTREME VIBRATION RESISTANCE

★ OTHER SIZE, MATERIAL ARE AVAILABLE UPON REQUEST

 

THICK WALL SECTION
SELF TAPPING THREAD INSERTS W. THREE CUTTING HOLE - THICK WALL SECTION

 

SELF TAPPING THREADED INSERT W. SLOTTED PIN

SELF TAPPING THREADED INSERT
W. THREE CUTTING HOLE

MATERIAL AVAILABLE: 
STEEL, STAINLESS STEEL, ALUMINUM, ALUMINUM ALLOY, BRASS

FOR USE IN THICK WALL OR CLOSE TO AN EDGE

ADVANTAGE:
1.HIGH PULL-OUT STRENGTH
2.HIGH TORQUE RESISTANCE
3.STRONG WEAR RESSTANCE THREAD
4.FAST, EASY INSTALLATION
5.EXTREME VIBRATION RESISTANCE

★ OTHER SIZE, MATERIAL ARE AVAILABLE UPON REQUEST

 

THICK WALL SECTION
SELF TAPPING THREAD INSERTS W. THREE CUTTING HOLE - THICK WALL SECTION

 

SELF TAPPING THREAD INSERTS - SLOTTED SERIES

SELF TAPPING THREAD INSERTS
SLOTTED SERIES

MATERIAL AVAILABLE: 
STEEL, STAINLESS STEEL 303 (A1), STAINLESS STEEL 316 (A4 / 18-10), BRASS C3604

SURFACE FINSIH AVAILABLE: 
CR3 WHITE/YELLOW ZINC PLATED

CHARACTERISTICS: 
1.EASY TO INSTALLED.
2.DESIGNED TO REPLACE SPRING COIL.
3.PROVIDE STRONG THREADS FOR WEAK MATERIAL LIKE ALUMINUM OR PLASTIC.
4.ABLE TO INSTALL FOR VIBRATING ENVIRONMENT.

APPICATIONS: 
1.CAN BE APPLIED TO DIFFERENT MATERIAL SUCH AS PLASTIC, ALUMINUM, CAST IRON.
2.DESIGNED TO APPLY IN WEAK MATERIAL WHERE THREADS ARE FRENQUENTLY USED.

★ OTHER SIZE, MATERIAL ARE AVAILABLE UPON REQUEST

 

SELF TAPPING THREAD INSERTS - SLOTTED SERIES

 

SELF TAPPING THREADED INSERT MANUAL INSTALLATION TOOLS

SELF TAPPING THREADED INSERT
MANUAL INSTALLATION TOOLS

I. HOLE SIZE: 
RECOMMENDED HOLE SIZE IS INDICATED ON EACH DATA SHEET AND IS INTENDED TO BE FOR REFERENCE ONLY. HOLE SIZE MAY NEED TO BE INCREASED OR DECREASED DEPENDING ON BASE MATERIAL, INSTALLATION TORQUE OR PERFORMANCE REQUIRED. OPTIMUM HOLE SIZE SHOULD BE DETERMINED BY REQUESTING SAMPLES & INSTALLING THEM IN THE INTENDED MATERIAL.

II. HOLE DEPTH: 
IN THRU HOLE APPLICATIONS THE INSERT LENGTH SHOULD NOT EXCEED THE MATERIAL THICKNESS. IN BLIND HOLE APPLICATIONS THE HOLE DEPTH SHOULD BE 1.2XINSERT LENGTH AND THIS VALUE IS INDICATED ON MOST DATA SHEETS.

III. COUNTERSINK 
A 60°COUNTERSINK IS REQUIRED FOR MOST MATERIALS TO INSURE A FLUSH SURFACE AFTER INSTALLATION.

IV. WALL THICKNESS 
WALL THICKNESS SHOULD BE 0.35 TO 0.5 X HOLE DIAMETER DEPENDING ON BASE MATERIAL.

★ OTHER SIZE, MATERIAL ARE AVAILABLE UPON REQUEST

 

   

SPEED PIN RIVET DRIVE PIN RIVET

SPEED PIN RIVET / DRIVE PIN RIVET

MATERIAL AVAILABLE FOR SPEED PIN RIVET (DRIVE PIN RIVET): 
BODY: ALUMINUM 2117 / STAINLESS STEEL 302 (INOX A2/18-8) / STEEL 1006
PIN: ALUMINUM 2024 / STAINLESS STEEL 304 (INOX A2/18-8) / STEEL 1022

FINISH SURFACE AVAILABLE FOR SPEED PIN RIVET (DRIVE PIN RIVET): 
PLATING: CR3 WHITE ZINC PLATED/ CR3 YELLOW ZINC PLATED/ CR3 BLACK ZINC PLATED/ ANODIZED/CLEAN

ADVANTAGES OF SPEED PIN RIVET (DRIVE PIN RIVET): 
1.SPEED PIN RIVET IS FAST AND EASY TO INSTALL.
2.NO SPECIAL INSTALLATION TOOL IS REQUIRED FOR SPEED PIN RIVET, JUST A HAMMER WILL DO.
3.VARIOUS MATERIALS ARE AVAILABLE FOR SPEED PIN RIVET.
4.VARIOUS HEAD STYLES ARE AVAILABLE FOR SPEED PIN RIVET.
5.SPEED PIN RIVET WILL NOT DAMAGE THE APPLICATION SURFACE
6.SPEED PIN RIVET CAN BE RUST RESISTANT.
7.SPEED PIN RIVET CAN BE APPLIED TO WIDE THICKNESS.
8.THE APPEARANCE LOOKS GOOD AFTER INSTALLATION.

★ OTHER SIZE, MATERIAL ARE AVAILABLE UPON REQUEST
★Available Size:5/32"、5/16"、3/16"、3/8"、1/8"、1/4"、

MALE FEMALE RIVET

MALE FEMALE RIVET

MATERIAL: ALUMINUM 5052 BRASS 2600 STAINLESS STEEL 302 / 410

APPLICATION : TABLEWARE

★ OTHER SIZE, MATERIAL ARE AVAILABLE UPON REQUEST

 

  

REBITADOR MANUAL

REBITADOR MANUAL

 

WEIGHT：0.6kg (1.32lb)
RIVET SIZE：2.4mm(3/32"),3.2mm(1/8"),4.0mm(5/32"),4.8mm(3/16").

RIVET MATERIAL：ALUMINUM & BRASS

RIVET FETURE：
1.INSTALL WITHOUT PRODUCING ANY HARMFUL MARK.
2.EASY, FAST & SAFE INSTALLATION.

ALL STAINLESS STEEL BLIND RIVET TS. SSASS. SERIES

ALL STAINLESS STEEL BLIND RIVET
TS.SSASS SERIES

MATERIAL AVALIABLE: 
RIVET: STAINLESS STEEL 302/ 316 (INOX A2/ A4/ 18-8/ 18-10)
SHAFT: STAINLESS STEEL 302/ 316 (INOX A2/ A4/ 18-8/ 18-10)

FINISH SURFACE AVALIABLE: 
RIVET: SELF COULOURED
SHAFT: SELF COULOURED

ADVANTAGES OF SS-S BLIND RIVET:
1.PROVIDE STRONG HOLDING FOR APPLICATION.
2.LOW IN COST COMPARE WITH BOLT AND NUT.
3.IDEAL FOR WIDE RANGE APPLICATION.
4.AVAILABLE IN DOME, COUNTERSUNK OR LARGE FLANGE STYLE.
5.FAST AND EASY TO INSTALL.
6.PROVIDE HIGH TENSILE AND SHEAR STRENGTH COMPARE WITH ALUMINUM OR STEEL.
7.IDEAL FOR RUST RESISTANCE APPLICATION.

★ OTHER SIZE, MATERIAL ARE AVAILABLE UPON REQUEST

 

ALL STEEL BLIND RIVET TS.SAS. SERIES

ALL STEEL BLIND RIVET
TS.SAS. SERIES

MATERIAL AVALIABLE: 
RIVET: STEEL 1006
SHAFT: STEEL 1018~1022

FINISH SURFACE AVALIABLE: 
PLATING: CR3 WHITE/ YELLOW/ BLACK ZINC PLATED/ CR3 ZINC NICKEL PLATED...ETC
COLOURED: YELLOW/ RED/ BLACK/ WHITE...ETC.

ADVANTAGES OF S-S BLIND RIVET: 
1.PROVIDE STRONG HOLDING FOR APPLICATION.
2.LOW IN COST COMPARE WITH BOLT AND NUT.
3.IDEAL FOR WIDE RANGE APPLICATION.
4.AVAILABLE IN DOME, COUNTERSUNK OR LARGE FLANGE STYLE.
5.FAST AND EASY TO INSTALL.
6.PROVIDE HIGH TENSILE AND SHEAR STRENGTH COMPARE WITH ALUMINUM.
7.IDEAL FOR RUST RESISTANCE APPLICATION.

★ OTHER SIZE, MATERIAL ARE AVAILABLE UPON REQUEST